NOCOR® E1540Water Soluble, Dry to Touch, Rust Preventative RELEASED: 2012-05-09
NOCOR® E1540 is water-soluble, rust-inhibiting oil which is normally used as a final treatment for phosphate rust proofing systems. The zinc phosphate coating will absorb the NOCOR® E1540 to produce a dry-to-the-touch, corrosion resistant and somewhat attractive finish.
BLOC N BOND 8550iInternally Accelerated Immersion Zinc Phosphate RELEASED: 2012-05-07
BLOC N BOND 8550i is a concentrated liquid chemical used to produce a zinc phosphate conversion coating on iron and steel parts. Coating weights can be adjusted in a range from 200-1,000 milligrams per square foot. This coating provides an excellent base for subsequent treatment with paint, rust preventatives, or lubricants.
Internally accelerated for easier control and upkeep
Imparts a coating that works well with oil and rust preventatives for greater corrosion protection of parts
BLOC N BOND MPremium-performance Immersion Manganese Phosphate RELEASED: 2012-05-07
BLOC N BOND M is a liquid chemical concentrate that produces a tightly bonded, microcrystalline, corrosion-resisting, manganese-nickel phosphate coating on iron and steel. It’s applied in conventional immersion processing equipment.
Produces uniform coatings on cast iron, low and high alloy steels, as well as, chilled, nitride, and cyanided ferrous metals
Internally accelerated, minimizing the need for tank side additives
Capable of producing 1,000-4,000 mg/ft2 coating weights
CID 5632Acidic Cleaner and Descaler RELEASED: 2012-05-07
CID 5632 is a concentrated blend of sulfuric and phosphoric acids with detergent and inhibitors. The acid cleaner removes rust and oxides from ferrous, some stainless steel, aluminum, and other nonferrous surfaces, and will also clean and remove oil and similar deposits from metal surfaces. However, it will not significantly attack the base metal, but only remove the oxides or corrosion sites
Also, used in removal of scale buildup found in zinc and iron phosphate equipment
Inhibited formula protects metal from being overly attacked/etched
MASTER BRITE 5719Organic Acid Brightener and Detergent RELEASED: 2012-05-07
MASTER BRITE 5719 is a slightly acidic liquid which will clean and brighten a variety of metals, including, copper, brass, zinc, and aluminum surfaces including castings and extrusions. In addition to brightening, MASTER BRITE 5719 can remove heavy soil deposits such as casting lubricants. Soiled, dull, and discolored metal can be cleaned and reconditioned or prepared for further processing or painting using this formula.
Cleans and brightens metals without the use of harsh mineral acids or caustic ingredients
Designed as an immersion cleaner, but also finds use as a spray or wipe-on cleaner
Can be used as an alternative to nitric or phosphoric acid for stainless steel passivation applications
CLEAN 7140HDHeavy-duty, Alkaline Degreaser for Spray and Immersion RELEASED: 2012-03-23
CLEAN 7140HD is a highly concentrated, heavy-duty spray cleaner specially designed for removing heavy grease and oil residues from ferrous parts. CLEAN 7140HD is an ideal choice for remanufacturing/rebuilding operations.
CLEAN 7140HD provides exceptional cleaning for removing heavy grease and oil residues without the use of solvents
Also compatible with many magnesium and zinc alloys as well as galvanized materials
Low foaming when used above 120°F
CLEAN 7140HD contains no V.O.C.
Can be recycled using XYBEX® equipment
Contains no solvents, borates, silicates, nitrites, phosphates, EDTA, NPEs, or amines
Typically provides one to three days of in-process corrosion inhibition on ferrous parts if not rinsed
Anodic Electrocleaner for Ferrous Metal RELEASED: 2012-03-21
CLEAN EC 5011 is a liquid, anodic (aka. reverse-current), alkaline electrocleaner designed to remove smut, oil and other difficult soils from steel prior to electroplating. This product contains no phosphates, chelators or V.O.C.’s and utilizes surfactants that are readily biodegradable and of very low aquatic toxicity
Better alternative for high strength steels, since hydrogen embrittlement risk is avoided
Great as a final cleaning method - smut-free part surface is achieved
Great for removing oxides, smut and impregnated, “difficult” drawing and hydroforming lubricants
Also finds use as a multi-metal soak cleaner – silicate to inhibit attack on nonferrous substrates
CLEAN IP 5811Alkaline Extrusion Cleaner RELEASED: 2012-03-20
CLEAN IP 5811 is an EDTA and phosphate-free, heavy-duty liquid alkaline cleaner used for cleaning aluminum extrusion and other multi-metal substrates. Its blend of caustic and potassium salts provide generous cleaning power for use on coil lines and other multi-stage washer systems.
CID 5140Inhibited Acidic Detergent for Metal Cleaning and Rust Removal RELEASED: 2012-03-05
CID 5140 is an inhibited phosphoric acid for the removal of rust and oxidation on ferrous materials and surfaces. It is easy to manage and out performs its competitors in difficult rust removal applications. Once the oxidation has been removed, an acid neutralization rinse or bath like CLEAN 2029 may be required.
Heavy-duty, fast-acting product for difficult corrosion removal on ferrous materials
Leaves a clean bare metal surface
Designed for use in immersion and ultrasonic tanks at ambient temperatures to 140°F (60°C)
TRIM® C270PR is formulated to meet the stringent environmental regulations specified under Japan’s Pollutant Release and Transfer Register (PRTR), and is a state-of-the-art synthetic coolant. C270PR provides excellent cooling and chip settling, good tramp oil rejection and machine cleanliness, and meets the need of the modern job shop for a single premium synthetic coolant for virtually all machining operations.
C270PR is compatible with a very wide range of materials including: cast iron, steels and copper alloys, as well as plastics and composites
Provides excellent corrosion inhibition on all common ferrous and nonferrous alloys
Does a great job in form grinding, drilling, tapping, and reaming operations without chlorine or sulfur-based EP additives
In addition to traditional grinding, C270PR is an excellent choice for electrolytic in-process dressing (ELID) grinding applications.
Extremely low carryoff for very low total operation costs
Very low foam and mist
Keeps your machines clean while leaving a soft, fluid film that protects the bare metal parts. This residual film is easily resoluble in coolant working solution to facilitate easy machine cleaning and minimize the buildup of sticky residues that can hold machine-destroying chips
Exceptional sump life and very good tramp oil rejection
A very low initial odor level which usually disappears after one to two days
CLEAN IP 5016 WCHeavy-duty Alkaline Cleaner with Low Residue RELEASED: 2011-09-26
CLEAN IP 5016 WC is an alkaline cleaner designed to remove drawing compounds, lubricants, and zinc phosphate coatings along with reactive lubes. It is formulated to provide good cleaning ability and dispersing characteristics. Very effective at cleaning metal extrusions after extruding process, where oil, lubricants, and other soils can be difficult to remove.
Developed for special cleaning needs of exotic metals, such as titanium, stainless steel, high-nickel alloyed steels, etc.
Formulated with biodegradable surfactants
Free-rinsing and leaves no contaminants behind
CLEAN IP 2026PFPhosphate-free Cleaner RELEASED: 2011-09-15
CLEAN IP 2026PF is a highly concentrated liquid parts-washing compound for use in spray and immersion washers, including ultrasonics. This product is safe and effective on aluminum alloys and steel parts, as well as cast iron, brass, zinc, titanium, and magnesium. CLEAN IP 2026PF provides good detergency and long life for the removal of coolants, straight oils, corrosion inhibitors, and all types of metalworking fluids. CLEAN IP 2026PF has been found to be highly useful in the diverse and difficult cleaning applications found within engine and transmission remanufacturing operations.
Prevents flash rusting on steel or cast iron parts if not rinsed
In many cases it minimizes or eliminates the need for multiple cleaning products since it is very effective in spray and immersion application. Excellent choice for two- or three-stage washer systems.
Provides long bath life
Environmental approvals are simplified because CLEAN IP 2026PF contains no nitrites, barium, phenols, phosphates, or butyl cellusolve; this formula is NPE free and has no SARA 313 reportable ingredients
Low foaming for use in high-pressure spray washers when used above 120˚F
Low-foam Machine Tool Sump and System Cleaner RELEASED: 2011-07-21
Whamex XT™ is a low foam, safe, fast-acting, concentrated formula that will save machine cleaning downtime while removing the oily residues, scums, and insoluble soap deposits that reduce coolant life. Whamex XT is made for cleaning out machine tool sumps and larger systems, coolant supply lines, and coolant recycling equipment. Whamex XT is compatible with most waste treatment (including ultrafiltration) and will not degrade TRIM® metalworking fluids when used as directed.
A very specialized formula that draws on Master Chemical’s knowledge of coolant formulation and many years of hands-on experience in machine cleanouts
Quickly breaks down and lifts off insoluble scum deposits hidden in lines and difficult to reach areas - getting rid of these residues is one of the best ways to extend coolant life in your system
Very hard water tolerant allowing it to be effective in raw water or used coolant
Environmental approvals are simplified because Whamex XT contains no nitrites, phosphates, barium, phenols, or butyl cellusolve; this formula has very low V.O.C. content and no SARA 313 reportable ingredients
When used as directed below, this product is compatible with TRIM® brand synthetic, semisynthetic, and soluble oil coolants, as well as most competitive coolants. Will remove heavy soils from machines without affecting paints, coatings, seals, hoses, or skirting, and it won’t leave a slippery residue
Short-term corrosion inhibitors prevent flash rusting of machine surfaces and ways
CLEAN IP 5690Premium Acidic Detergent RELEASED: 2011-06-28
CLEAN IP 5690 is a liquid blend of detergents and inorganic acid, formulated expressly for the cleaning and conditioning of aluminum prior to coating. It is used in spray or immersion applications.
Free rinsing to minimize the cross contamination of subsequent baths
Low foaming for use in spray applications as well as agitated immersion baths
Cleans, brightens, or etches aluminum depending on time and temperature of process
PAINT RIP 2865 is a single package, room temperature paint stripper designed to remove powder coatings and other types of paint.
Single package formula for ease of use
Methylene Chloride-free
Operates at room temperature to conserve energy
Caustic-free
Safe on aluminum, magnesium, zinc, and ferrous metals
PLASTI PLEX 5311Liquid Plastic Fascia Cleaner RELEASED: 2011-06-17
PLASTI PLEX 5311 is a liquid, acidic plastic cleaner for removal of common soils, such as, mold release agents, plasticizers, UV stabilizers, and finishing dust.
Liquid version allows for automated chemical dosing
Improves the plastic surface, which is typically hydrophobic, for improved paint adhesion
Effectively cleans at low temperatures to reduce warping or distortion of parts
MASTER BRITE 5308A Copper and Brass Brightener RELEASED: 2011-06-16
MASTER BRITE 5308A and 5308B are a two-part acidic solution system designed to clean and brighten copper and brass parts.
Quickly removes light oxidation and oil
Concentrated formula can be used as low as 5%
Does not require heat
MASTER BRITE 5308BCopper and Brass Brightener RELEASED: 2011-06-16
MASTER BRITE 5308A and 5308B are a two-part acidic solution system designed to clean and brighten copper and brass parts.
Quickly removes light oxidation and oil
Concentrated formula can be used as low as 5%
Does not require heat
BLOC N BOND 8315Low-temperature, High-performance Zinc Phosphate and RELEASED: 2011-06-13
BLOC N BOND 8315 is a low-to moderate-temperature Zinc Phosphate process for steel and galvanized steel substrates. It is especially effective as a paint pretreatment, where light to medium coating weights are preferred.
Operates at energy-saving low
temperatures
Capable of superior salt spray performance
Low sludge formula
BLOC N BOND 8315RPLow-temperature, High-performance Zinc Phosphate and RELEASED: 2011-06-13
BLOC N BOND 8315 is a low-to moderate-temperature Zinc Phosphate process for steel and galvanized steel substrates. It is especially effective as a paint pretreatment, where light to medium coating weights are preferred.
Operates at energy-saving low temperatures
Capable of superior salt spray performance
Low sludge formula
CLEAN GP 5419General Purpose Cleaner RELEASED: 2011-06-03
CLEAN GP 5419 is a very effective blend of potassium phosphates, surfactants, and solvents for general purpose, floor, and spray or soak-tank cleaning.
Contains no carcinogens or strong alkali’s
Doesn’t fume or have irritating odor
Safe on a wide variety of surfaces
CLEAN GP 5327Heavy-duty, Natural-solvent, Emulsion Cleaner RELEASED: 2011-06-01
CLEAN GP 5327 is a blend of d-Limonene (natural-solvent) and detergents for use as a heavy-duty, general-purpose cleaner. CLEAN GP 5327 is safe for cleaning metals, ceramics, and glass surfaces.
Uses natural solvents in place of hazardous petroleum-based solvents
Capable of removing very tenacious soils, such as; asphalt, tar and parrifins.
TRI-CLPS® ADDITIVE 1 is a pH adjusting fluoric acid compound used in conjunction with the TRI-CLPS® 7200 series products. Complete instructions for use are contained in the TRI-CLPS® 7200 Product Data Bulletin.
TRI-CLPS® 7220Patented Conversion Coating for Aluminum RELEASED: 2011-05-18
TRI-CLPS® 7220 is a liquid coating chemical used to produce a complex zirconium, organic, trivalent chromium coating on aluminum, magnesium and zinc alloys. The coating, when properly applied, has excellent paint bonding properties and affords under film protection while maintaining the low surface resistivity demands of the electronics industries. The treatment can be applied as a dried-in-place (DIP) coating or, when used at higher concentrations, be rinsed prior to dry off.
TRI-CLPS® 7220 is a more user-friendly process when compared to harsh hexavalent chromium (Cr+4) conversion coating processes
Near colorless coating does not telegraph through most top coatings
Can be rinsed or used as a dry-in-place pretreatment
Operates at energy-saving low temperatures
Excellent choice for treating aluminum, magnesium, and zinc substrates
Patented, high-performance, low-temperature, conversion coating for the replacement of iron and zinc phosphates.
Lower or no energy costs! ZIRCA-SIL™ 18 I operates at 70°F and usually not higher than about 110°F that can occur from carry-over heat from previous stages.
ZIRCA-SIL™ 18 I is phosphate free! With this process there is no concern of phosphates contaminating your effluent.
Lower water usage! Because in some cases fewer stages can be used in the process, the amount of overflow water will be less and overall usage of water will be significantly less.
Faster process time! By using the ZIRCA-SIL™ 18 I process you can significantly reduce the process time as a result of the reduction in stages required. ZIRCA-SIL™ 18 I typically coats much faster than zinc phosphates, without compromising performance.
Easy to control! Unlike zinc phosphate, the ZIRCA-SIL™ 18 I process requires fewer and much simpler controls.
ZIRCA-SIL™ 18 I is compatible with all paints and metals!
PAINT RIP 2860 is a single package, Methylene Chloride-free paint stripper for multi-metal.
Single package formula for ease of use
Methylene Chloride-free
Operates at room temperature to conserve energy
Caustic-free
Safe on aluminum, magnesium, steel, and zinc
CID 5683Acidic Detergent RELEASED: 2011-05-10
CID 5683 is a concentrated phosphoric acid detergent that excels at cleaning a variety of metals. CID 5683 will remove rust from steel and cast iron, and other oxides on stainless steel, aluminum, and some other nonferrous metals.
Concentrated formula
Removes organic and inorganic soils
Used at ambient temperatures to reduce energy costs or can be heated for difficult applications
Spray or immersion capable
Use as part of a system or as a stand-alone process
CLEAN IP 5769Non-silicated, Near-neutral Cleaner with Short-term Corrosion Protection RELEASED: 2011-04-03
CLEAN IP 5769 is a mild alkaline, highly-concentrated liquid parts washing compound/corrosion inhibitor for use in spray washers. This product is safe and effective on aluminum or steel alloy parts, as well as cast iron. CLEAN IP 5769 provides good detergency through its unique organic surfactants package for the removal of coolants, straight oils, corrosion inhibitors, and all types of metalworking fluids.
Non-silicated
Leaves a non paint interfering film for corrosion protection
Splits oil for easy skimming/removal
Uses biodegradable surfactants
CLEAN IP 5835PFPhosphate-free, Multi-purpose Cleaner RELEASED: 2011-04-03
CLEAN IP 5835PF is a phosphate-free, alkaline cleaner designed for use in pretreatment systems, parts washers, and agitators. It is multi-metal safe, including zinc and aluminum substrates. Its special formula allows it to be used in areas where local regulations require a reduction in phosphates.
Phosphate free
Free rinsing, which helps reduce alkaline carryover to subsequent stages
ZIRCA-SIL™ ADDITIVE 1 is an acidic adjustment additive for making minor reductions in operating pH of a working
ZIRCA-SIL™ 18 I bath. This material is used in the event that the pH rises above the recommended (max.) limit, as
suggested on the Data & Information sheet.
CLEAN IP 5895Concentrated Low Temperature Spray Cleaner RELEASED: 2011-03-24
CLEAN IP 5895 is a heavy duty liquid alkaline cleaner for use on multi-metal substrates. It is most often used in high pressure spray applications and it is an excellent performer in single stage cleaning operations.
Low foaming formula
Rejects tramp oil well for easy removal which translates into solution life
Effectively removes oil, grease, smut, and other difficult soils
Safe on aluminum and zinc
Suitable for agitated immersion application too
HEAT SEAL 2052Heat Seal Layer RELEASED: 2011-03-16
HEAT SEAL 2052 is an insulating layer that locks the heat in the bath, while also reducing fumes that typically occur during paint stripping operations.
Zirca-Sil™ Additive 2 improves the quality of the Zirca-Sil™ 18 coating by preventing the accumulation of detrimental ferrous iron contaminates in the bath when significant quantities of steel parts are processed.
Zirca-Sil™ Additive 2 is also used to rid some processes of unwanted organic contaminates
BLOC N BOND 9900Premium Performance Iron Phosphate RELEASED: 2011-03-15
BLOC N BOND 9900 is a unique detergent iron-phosphate chemical which is based on ammonium salts and is virtually sodium-free. It effectively cleans and phosphates ferrous metals, and can often times reduce sludge in the bath. Additionally it vitually eliminates residue and water spotting effects, which can often “telegraph” through or react adversely with some paints, such as high solids type.
Unique accelerator package to develop higher coating weights
Produces a residue-free coating
Fluoride free
Used in three or five stage systems
Spray or Immersion use
RINSE AID 12Liquid Rinse Aid RELEASED: 2011-03-15
RINSE AID 12 is used in final rinse stages to reduce water spotting effects that sometimes cause paint adhesion failure.
NUTRA 18Buffered Alkaline pH Adjuster for Rinse Stages RELEASED: 2011-03-10
NUTRA 18 is a liquid alkaline chemical that provides steel with temporary protection against flash rust. This product is especially suitable for use in the neutralization of steel surfaces after acid pickling or phosphating.
Built-in temporary corrosion inhibition
Buffered formula provides good pH consistency
Can be added manually or by metering pump
BLOC N BOND 9762Low-temperature, High-performance Iron Phosphate RELEASED: 2011-03-07
BLOC N BOND 9762 is a liquid iron phosphate used in five-stage applications where higher performance coatings are required. BLOC N BOND 9762’s formula permits it to coat multi-metal surfaces, such as, steel, aluminum, galvalume and galvaneal substrates at lower than traditional operating temperatures.
Operates at low temperatures which translates into valuable energy savings
Low foaming formula designed for spray applications
Accelerator package produces above average coating weights
PAINT RIP 2830 is a liquid caustic potash-based paint stripper designed for the most severe applications on steel and cast iron.
Uses liquid potash to improve safety over other hot caustic-type paint strippers that rely on dry potash; hence, eliminates chance for exothermic reaction.
Unique blend of additives for improved performance
Effective for the removal of e-coatings and other difficult paints
A more complete cleaner stripping job than straight caustic-based paint strippers
E-CLPS® 1900High-performance Environmentally-friendly Final Seal RELEASED: 2011-03-04
E-CLPS® 1900 is a chromium free liquid chemical used as the final seal for cleaned aluminum, steel, and galvanized metals, providing improved paint adhesion and corrosion resistance. E-CLPS® 1900 is a convenient to use liquid product which may be applied in either spray or immersion processes. E-CLPS® 1900 is considered a nonhazardous material both as a concentrate and as a working bath.
E-CLPS® 1900 is mostly used for aluminum applications that have a small amount of steel or galvanized parts mixed in
Works as a final seal for iron and zinc phosphates
In some processes, E-CLPS® 1900 can be used in place of iron phosphate or other pretreatment materials in order to reduce or elimate phosphates from waste stream
Simple to control
Free of heavy metals, toxic organics and has no V.O.C. content
E-CLPS® 2100High-performance Environmentally-friendly Final Seal RELEASED: 2011-03-02
E-CLPS® 2100 is a chrome free, nonphosphate liquid coating chemical used to produce a clear, nearly colorless, chemical Dried-In-Place (DIP) coating on aluminum and zinc alloys. The coating, when properly applied, has excellent paint bonding properties and affords well under paint-film protection.
Near colorless coating eliminates potential for telegraphing paint defects
Dry-in-place coating eliminates need for rinse stage pretreatment
Premium salt spray performance from a nonchrome, nonphosphate product that is a great choice for aluminum architectural work
Ambient temperature capable, which translates to great energy savings
BLOC N BOND 915Premium Performance, Concentrated Detergent Iron Phosphate for Multi-metal RELEASED: 2011-02-23
BLOC N BOND 915 is a premium performance detergent iron phosphate which is based on ammonium salts and is virtually sodium free. Its blend of unique accelerator additives distinguish this iron phosphate from others.
The BLOC N BOND 915 should be used when optimal salt spray performance is required on aluminum and steel materials.
Extreme salt spray performance
Minimizes residue and water spotting effects which sometimes telegraph through some paints
Can be used in three or five-stage spray or immersion process.
Multi-metal safe
E-CLPS® 1980High-performance Environmentally-friendly Final Seal RELEASED: 2011-02-23
E-CLPS® 1980 is a liquid chrome-free, nonphosphated pretreatment chemical used to form a paint bonding and corrosion-resistant surface treatment on zinc, aluminum, magnesium, ferrous, and cuprous alloy surfaces. E-CLPS®
1980 may be applied by spray or immersion and is used as a final seal over iron and zinc phosphates (for higher salt spray performance) or as a stand-alone pretreatment (without phosphate) for general applications.
E-CLPS® 1980 is a nonhazardous material which reduces or eliminates workplace hazards and is free of heavy metals, toxic organics and it has no V.O.C. content.
E-CLPS® 1980 is mostly used for galvanized applications that have a small amount of steel or aluminum parts mixed in
Can be used as a replacement for traditional pretreatments
Operates at ambient temperatures, which translates into large utility cost savings
PERK 113Cleaning Booster RELEASED: 2011-02-21
PERK 113 is a concentrated blend of detergents and solvents for cleaning systems.
MASTER BRITE 5001 is a blend of detergents, solvent, and acids for cleaning and brightening of aluminum surfaces, including castings and extrusions, MASTER BRITE 5001 is used in immersion operations only.
Concentrated formula for optimum performance and economy
Removes light oxides and brightens dull and discolored surfaces
Operates at room temperature, saving on energy cost
BLOC N BOND 9739SCSingle-stage Detergent Iron Phosphate for High-pressure Spray RELEASED: 2011-02-13
BLOC N BOND 9739SC is an acidic liquid iron phosphate designed to clean and coat multi-metal surfaces using manual power spray equipment and steam generators.
Detergent package quickly and effectively cleans surface prior to producing phosphate coating
Accelerator ingredients quickly produces iron phosphate coating
Can be used at low to moderate temperature
Equipment can be constructed of mild steel
BLOC N BOND 916Premium Performance, Concentrated Detergent Iron Phosphate RELEASED: 2011-02-11
BLOC N BOND 916 is a premium performance detergent iron phosphate which is based on ammonium salts and is virtually sodium free. Its blend of unique accelerator additives distinguish this iron phosphate from others. The BLOC N BOND 916 should be used when optimal salt spray performance is required on steel materials.
Extreme salt spray performance on steel substrates
Minimizes residue and water spotting effects which sometimes telegraph through some paints
Can be used in three-or five-stage spray or immersion process.
CID 5640 is a premium liquid acidic spray cleaner and metal surface conditioner. It was developed to provide excellent cleaning and slight etching of ferrous surfaces. It can be used as a cleaner to remove soils and at the same time, remove light rust while unpassivating or conditioning a ferrous surface for further treatment. CID 5640 can be used as part of a pretreatment (pre-paint) system for cleaning laser oxides and soils or as a stand-alone process for conditioning ferrous materials.
Unique formula permits this material to be used without the use of a subsequent alkaline cleaner
Exceptional detergency package capable of removing organic soils typically not removed by lesser-built acid cleaner
WELD WIPE is a nonhazardous liquid designed to prevent spattering during welding operations on ferrous metals. WELD WIPE is not an oil based product, but a surfactant based system which actually aids subsequent cleaning operations.
Easily cleaned off using water-based cleaners
Synthetic formula minimizes residue
When properly used saves many hours of sanding prior to finishing operations
CLEAN IP 5818Low-foaming, Heavy-duty, Multi-purpose Cleaner RELEASED: 2011-02-11
CLEAN IP 5818 is a liquid, low-foaming alkaline spray cleaner for multi-metal parts. Its formula exhibits excellent rinsing characteristics, so as not to contaminate subsequent rinse or chemical stages. Great for pre-paint spray pretreatment systems as well as soak and agitated immersion operations.
Wide operating temperature range capable of running as low as 100°F.
Very effective at removing oil, grease and carbonaceous soils in severe application, such as, vehicle remanufacturing operations.
Very low foaming formula for extreme spray pressures, yet suitable for immersion applications.
M CONDITIONERPhosphate Activator RELEASED: 2011-02-10
M CONDITIONER is a powered metal conditioner used to create finer grained and more uniformed phosphate coatings. It is particularly effective in preventing course, irregular coatings that sometimes occur when phosphate is applied after strong alkaline or acid processes. It is also extremely effective in producing higher quality manganese phosphate coatings on steel.
Powdered formula with no fillers
Helps to neutralize and condition steel surfaces which translates into denser more uniform phosphate coating
Easily diluted in water
BLOC N BOND 9730Economical Iron Phosphate, One-step Clean and Coat RELEASED: 2011-02-06
BLOC N BOND 9730 is a liquid-detergent iron phosphate used for cleaning and coating of ferrous, zinc, and aluminum surfaces. It performs well at low to moderate temperatures in a three or five stage spray washer system.
Formulated with detergents to provide improved cleaning
Equipment may be constructed of mild steel
Fluoride free
Removes light oxides from aluminum
NUTRA 51Alkaline pH Adjuster RELEASED: 2011-02-02
NUTRA 51 is a moderately alkaline material used for neutralizing acidic processes such as iron phosphate baths. It may also be used for alkaline pH adjustment of acidic solutions prior to disposal.
Concentrated powder formula
Can be used with iron phosphate baths
Can be used to adjust pH for disposal of spent acidic solutions
PHOS ADJUST 1 is an acidic pH adjustment solution for iron and zinc phosphate baths. By adding PHOS ADJUST 1 you lower the pH while also replenishing other important ingredients. PHOS ADJUST 1 may be used whenever a lower pH is desired with a iron or zinc phosphate bath.
CLEAN IP 5734Concentrated Liquid Alkaline Etchant RELEASED: 2011-01-26
Liquid etching-type alkaline cleaner for aluminum extrusions, which can also be used as a caustic descale cleaner for pretreatment washer systems, and other solution recirculating systems. CLEAN IP 5734 retains aluminum, other metals and soils in solution, so that scaly deposits or soil redepositions do not occur.
Does not build up hard water deposit on tank surfaces and heating elements, thus reducing maintenance costs
Liquid formula for ease of use and metering
Can be used in spray or immersion operations
PASS 151Liquid Deoxidizer for Aluminum RELEASED: 2011-01-26
PASS 151 is a liquid chemical used to deoxidize aluminum and its alloys without the formation of objectionable smut. In addition, PASS 151 can also be used for passivation of stainless steel.
BLOC N BOND 9741Concentrated, Value-priced Iron Phosphate RELEASED: 2011-01-25
BLOC N BOND 9741 is an immersion-type detergent iron phosphate used for cleaning and coating of ferrous, zinc, and aluminum surfaces. It performs well at low to moderate temperatures in a three or five stage pretreatment system.
Formulated with detergents to provide improved cleaning
Equipment may be constructed of mild steel
Fluoride free
Removes light oxides from aluminum
At higher concentrations BLOC N BOND 9741can be used to remove light rust/oxides
BLOC N BOND 9737High-performance, Multi-metal Detergent Iron Phosphate RELEASED: 2011-01-24
BLOC N BOND 9737 is a liquid detergent, iron phosphate used for cleaning and coating of ferrous, zinc, and aluminum surfaces where good performance and value are desired
Accelerator package produces a dense iridescent coating.
Meets the performance of military specifications TT-C490C, Type II (five stages mandatory)
Can be used in three-or five-stage spray applications.
Can also be used as a light rust remover for ferrous metals (typical concentrations: 10%-20% b.v.) Consult your local Master Chemical Representative for operating parameters.
CID 5604Acid Spray Cleaner for Removal of Welding and Laser Oxides RELEASED: 2011-01-24
CID 5604 is a liquid, free-rinsing acid cleaner formulated for the removal of welding, and laser oxides from steel surfaces, while simultaneously removing oils and other surface contaminants. Its low-foaming characteristics make it suitable for use in mechanical spray washing equipment.
Low foaming
Can be used within a pretreatment line with or without a subsequent alkaline cleaner stage
Blend of inorganic acids for excellent oxides removal
CID 5922Inhibited Acid Cleaner for De-scaling Equipment RELEASED: 2011-01-24
CID 5922 is an inhibited acid cleaner designed to clean and de-scale washer equipment by dissolving ferric phosphate scale and sludge buildup from tank walls, heating elements, and recirculation pipes
Quickly removes hard water buildup from metal surfaces
Inhibited formula reduces attack on equipment components
Typically operates at ambient temperatures
CLEAN IP 5855Premium Aluminum Cleaner RELEASED: 2011-01-21
CLEAN IP 5855 is designed for cleaning and brightening of aluminum materials without the issue of etching or attack of the substrate. CLEAN IP 5855 can be used on aluminum cleaning lines or as part of a pretreatment process prior to painting or powder coating.
Inhibited formula minimizes staining and etching of nonferrous metals
Capable of cleaning ferrous metals
Performs well in immersion or in spray applications
CLEAN IP 5940Multi-metal Immersion Cleaner RELEASED: 2011-01-19
CLEAN IP 5940 is a concentrated alkaline cleaner designed for use in immersion washing equipment. Its heavy duty formula produces excellent results in removal of difficult soils such as tenacious lubricants and drawing compounds.
Multi-metal formula
Built to remove the most difficult shop soils
Used in static or agitated immersion tanks
PERK 10Cleaning Booster for Difficult Soils RELEASED: 2011-01-18
PERK 10 is a highly concentrated blend of detergents and solvent designed for removal of difficult soils on multi-metal surfaces. PERK 10 may be added to alkaline and acid cleaning baths to boost their effectiveness
CLEAN IP 5839MTHeavy-duty, Multi-purpose Cleaner for Steel RELEASED: 2011-01-17
CLEAN IP 5839MT is a liquid, free rinsing, alkaline cleaner designed expressly for the cleaning of ferrous metals. The formula can also be used on aluminum and zinc at a lower operating temperature.
Low foaming
Free rinsing characteristics minimizes carryover to subsequent stages
Concentrated formula suitable for immersion applications
Wide temperature range for ease of use
BLOC N BOND X-CELZinc Phosphate Accelerator RELEASED: 2011-01-10
BLOC N BOND X-CEL is a liquid accelerator additive used to control the reaction of a zinc phosphate bath, to permit successful coating.
BLOC N BOND 9740Concentrated, Low-cost Iron Phosphate RELEASED: 2011-01-09
BLOC N BOND 9740 is a liquid-detergent iron phosphate used for cleaning and coating of ferrous, zinc, and aluminum surfaces. It performs well at low-to moderate-temperatures in a three or five stage spray washer system.
Formulated with detergents to provide improved cleaning
Equipment may be constructed of mild steel
Fluoride free
Removes light oxides from aluminum
BLOC N BOND 8455Immersion Zinc Phosphate RELEASED: 2010-10-15
BLOC N BOND 8455 is a liquid chemical concentrate that produces a tightly bonded, microcrystalline, corrosion-resisting, paint-bonding, zinc phosphate coating on iron, steel, and zinc. It’s applied in conventional immersion processing equipment.
Improves salt spray over iron phosphate systems
This product is particularly suited for providing a slip resistant coating on nails
Wide operating temperature range for ease of use and potential energy savings
E-CLPS® 1750High-performance Environmetally-friendly Final Seal RELEASED: 2010-10-15
E-CLPS® 1750 is a chromium-free, liquid chemical used as the final seal for cleaned steel, galvanized, and aluminum; and provides improved paint adhesion and corrosion resistance. E-CLPS® 1750 is a convenient to use liquid product which may be applied in either spray or immersion processes. E-CLPS® 1750 is considered a nonhazardous material both as a concentrate and as a working bath.
E-CLPS® 1750 is mostly used for steel applications that have a small amount of aluminum or galvanized parts mixed in.
In some cases can be used as a non-phosphated pretreatment to replace iron phosphate
Capable of operating at energy-saving low temperatures
NUTRA 10Buffered Alkaline pH Adjuster for Rinse Stages RELEASED: 2010-10-15
NUTRA 10 is a liquid alkaline solution designed for use in rinse water, whereas the rinse stage follows an acidic process, such as a pickle or deoxidizer.
Z CONDITIONER 6Zinc Phosphate Crystal Conditioner for Steel RELEASED: 2010-10-15
Z CONDITIONER 6 is a powdered, water-soluble chemical used to condition ferrous metal surfaces where a dense, uniform, and finely crystalline phosphate coating is desired. It is particularly effective in preventing the formation of coarse, irregular coatings, often occurring on surfaces previously cleaned in strong alkaline solutions or pickled in acidic solutions. It is suitable for steel and galvanized steel substrates.
Highly concentrated formula translates to lower consumption
No fillers used, which improves performance over diluted zinc phosphate conditioners
TRIM® VHP® E814 is a low- to no-foam, chlorine-free, long-life, soluble oil. This versatile emulsion performs well in most machining and grinding applications but excels in high-pressure environments where many fluids fail. VHP E814 allows you to realize the maximum productivity benefits from your high velocity through-the-tool coolant delivery systems. The stable and predictable performance of VHP E814 makes it the first choice for high quality, consistent parts manufacturing.
Stable, low-foam formula extends useful life without need for tank side defoamer additions
Nonchlorinated, extreme-pressure (EP) additives control built-up edge
Delivers excellent material removal rates and finishes on applications as difficult as gun drilling
Proven performer in difficult creepfeed grinding operations
Easily recycled or disposed of without special handling or equipment
Contains no DEA, chlorine, nitrites, or phenolic compounds
Forms stable emulsion in hard water environments
BLOC N BOND 9777Premium Performance, Detergent Iron Phosphate RELEASED: 2010-09-30
BLOC N BOND 9777 is a unique detergent iron phosphate chemical which is totally based on ammonium salts and is virtually sodium-free. It effectively cleans and phosphates ferrous metals and can often times reduce sludge in bath. Additionally it reduces the amount of residue and water spotting effects, which can often “telegraph” through or react adversely with some paints, such as high solids type.
Multi-metal capabilities
Powder and residue-free iron phosphate coatings
Used in two-, three-, and five-stage spray systems
Fluoride-free
Capable of also being used in immersion applications
Capable of running as low as 100°F
E-CLPS® 1700High-performance Environmentally-friendly Final Seal RELEASED: 2010-09-30
E-CLPS® 1700 is a chromium free liquid chemical used as the final seal for cleaned steel , galvanized, and aluminum providing improved paint adhesion and corrosion resistance. E-CLPS 1700 is a convenient to use liquid product which may be applied in either spray or immersion processes. E-CLPS 1700 is considered a non- hazardous material both as a concentrate and as a working bath.
E-CLPS 1750 is mostly used for steel applications that have a small amount of aluminum or galvanized parts mixed in
NUTRA 11 is a liquid alkaline product designed for neutralizing acidic solutions prior to disposal. It may also be used to adjust the pH of acidic baths.
Patented, High-performance, Low-temperature, Conversion Coating for the Replacement of Iron and Zinc Phosphates.
Lower or no energy costs! ZIRCA-SIL™ 18 operates at 70°F and usually not higher than about 110°F that can occur from carry-over heat from previous stages.
ZIRCA-SIL™ 18 is phosphate free! With this process there is no concern of phosphates contaminating your effluent.
The ZIRCA-SIL™ 18 process does not produce sludge! Unlike typical iron and zinc phosphate systems, ZIRCA-SIL™ 18 will not generate the heavy sludge or scale that clogs nozzles, adheres to heating tubes and exchangers, and must be cleaned every few months from tanks and be hauled away.
Lower water usage! Because in some cases fewer stages can be used in the process, the amount of overflow water will be less and overall usage of water will be significantly less.
Faster process time! By using the ZIRCA-SIL™ 18 process you can significantly reduce the process time as a result of the reduction in stages required. ZIRCA-SIL™ 18 typically coats much faster than zinc phosphates, without compromising performance.
Easy to control! Unlike zinc phosphate, the ZIRCA-SIL™ 18 process requires fewer and much simpler controls.
ZIRCA-SIL™ 18 is compatible with all paints and metals!
CLEAN IP 5842HPHeavy-duty Steel Cleaner for Spray or Immersion RELEASED: 2010-09-30
CLEAN IP 5842HP is a liquid, free rinsing alkaline cleaner. It is designed expressly for the cleaning of steel, zinc, and aluminum parts. Its low foam profile makes it suitable for use in mechanical spray washing equipment.
Suitable for high-pressure washers and agitated tanks
Reduces alkaline carryover into subsequent stages
Non-silicated formula eliminates potential for silicate drydown interference
Capable of operating within a wide temperature range
TRIM® MicroSol® 685lf is a high-lubricity, low-foaming semisynthetic microemulsion coolant. The formula offers the performance of a heavy-duty soluble oil with the cleanliness of a semisynthetic. It provides excellent cooling and mechanical lubricity, along with the machine friendly characteristics you expect from a premium TRIM® coolant.
Low foam and low mist make it an excellent choice for high-pressure, high-volume coolant systems
Excellent alternative to chlorinated soluble oils on high-silica aluminum alloys
Reduces oil mist and residues often associated with high-lubricity alternatives
Has exceptional sump life without the use of tank side additives
Contains no nitrites, triazines, phenols, or sulfurized EP additives
Provides superior corrosion inhibition on all ferrous and nonferrous metals
Forms stable microemulsion in hard water environments
Compatible with a very wide range of material including aluminum, magnesium and copper alloys, cast iron, steels, stainless steels, and many plastics and composites
Keeps machines very clean while leaving a soft fluid film for ease of cleaning and reduced maintenance
Requires no special disposal or recycling techniques
TRIM® E850Premium Emulsion RELEASED: 2009-12-07
TRIM® E850 is a proprietary blend of new “green” vegetable-based technology and premium traditional lubricity additives to yield a very high-performance, easy-to-maintain metal removal fluid. This premium emulsion is operator friendly because of its mild contact nature and low chemical initial-charge odor. E850 is robust enough to deliver extended useful life and avoid rancid odors normally associated with traditional emulsions. The unparalleled physical lubricity delivers exceptional surface finish on difficult-to-machine aluminum alloys, exotics, stainless, and high-tensile strength steels.
Delivers unparalleled lubricity
Very long sump life and low carryoff rates result in low operating cost
Low product odor
Mild operator contact properties
Provides superior results in a wide range of operations
Excellent corrosion resistance on both nonferrous and ferrous materials
Superior wetting and penetration to the point of cut
Soft fluid film protects ways, chucks, and tool holders
Product contains no chlorine, boron, phenol, nitride, copper, or triazine
Easily removed from parts for easy cleanup before assembly, painting, or plating operations
High performance without the use of chlorinated paraffins
TRIM® MicroSol® 485 is a long life semisynthetic, microemulsion coolant designed for ferrous metalworking operations and optimized for difficult working environments associated with cast iron. MicroSol 485 prevents leaching of elemental iron and thus eliminates clinkering and oxidation of ferrous micro fines. Formula delivers extended sump life versus previous generation semisynthetics. It provides excellent cooling along with the machine friendly characteristics you expect from TRIM® coolants. MicroSol 485 is value-priced and specifically designed for use on ferrous metals.
The most cost conscience MicroSol® offering
Dramatically extends useful life without the need for tank-side biocides or fungicidest
Provides superior corrosion inhibition on cast iron and eliminates “hot chip” and clinkering problemst
Contains no nitrites, triazines, phenols, chlorinated, or sulfurized EP additivest
Keeps machines very clean while leaving a soft fluid film for ease of cleaning and reduced maintenancet
Requires no special disposal or recycling techniques
TRIM® C380 is a premium, synthetic, metalworking fluid optimized for high-tech ferrous materials including stainless steel and Inconel® which are widely used in aerospace, medical, and the electronics industries. C380 uses the best of the new ester technology to yield a very-high performance metal removal fluid that is, easy-to-use and maintain. The combination of the proven synthetic ester technology and nonhalogenated EP package produce very high levels of usable lubricity at the point of cut. C380 utilizes unique low-foam detergents to keep process soils from redepositing on machines and parts.
Ease of maintenance, low carryoff, and long sump life result in low operating cost
Clear, low foaming, low odor, and low mist create a clean manufacturing environment
High performance in a wide range of operations from general grinding to heavy-duty machining
Superior resistance to corrosion on ferrous materials including, titanium, Inconel, and high strength alloy steels
Easily removed from parts for easy cleanup before assembly, painting, or plating operations
Product readily rejects process oils such as hydraulic and way oils
Excellent surface finish in finish-grinding operations
PRTR compliant, no SARA 313 reportable chemistry
Product contains no chlorine, phenol, nitrites, copper, triazine, silicone, or phosphorous
TRIM® SC520 is a low-odor, low-cost semisynthetic, general-purpose, cutting and grinding fluid concentrate for the multi-material, multi-operational shop. SC520 uses a proven EP-additive package to control built-up edge, improve tool life, and has the wetting and cooling characteristics necessary for superior machining results on high-speed milling and turning operations. It also controls chip welding on soft, gummy materials like aluminum.
Good sump life in “stand-alone” machines
Low odor and mist
Effective in most grinding, sawing, drilling, and CNC turning and milling operations by varying concentrations
Provides sufficient lubricity to do down-the-hole operations in aluminum, cast iron, and most steels, including many stainless steels
Compatible with a very wide range of materials including cast iron, steels, copper, and aluminum alloys as well as most plastics and composites
Low-to-moderate foam with normal “flood” coolant application
Rejects tramp oils rapidly for easy recycling with good sump life
Easily recycled or disposed of using conventional techniques and equipment
TRIM® MicroSol® 585XT is a high-lubricity, semisynthetic, microemulsion coolant. Formula delivers extended sump life versus previous generation semisynthetics. It provides excellent cooling and mechanical lubricity, along with the machine friendly characteristics you expect from a premium TRIM® coolant. While it is particularly well suited for machining and grinding gray iron, it does very well in mixed metal situations. MicroSol 585XT has proven to be an exceptional machining fluid for titanium alloys.
Dramatically extends useful life without the need for tank-side biocides or fungicides
Compatible with a very wide range of material including cast iron, steels, copper, titanium and aluminum alloys, and many plastics and composites
Optimized combination of cooling and lubricity for titanium machining applications
Provides superior corrosion inhibition on cast iron and eliminates “hot chip” and clinkering problems
Excellent alternative to chlorinated soluble oils on high-silica aluminum alloys
Contains no nitrites, triazines, phenols, chlorinated, or sulfurized EP additives
Provides superior corrosion inhibition on all ferrous and nonferrous metals
Keeps machines very clean while leaving a soft fluid film for ease of cleaning and reduced maintenance
Requires no special disposal or recycling techniques
TRIM® MicroSol® 695 is a premium high-lubricity, semisynthetic microemulsion coolant. The formula offers the performance of a heavy-duty soluble oil with the cleanliness of a semisynthetic. It provides excellent cooling and mechanical lubricity, along with the machine-friendly characteristics you expect from a premium TRIM® coolant.
Excellent alternative to chlorinated soluble oils and semisynthetics on high-silica aluminum alloys
Keeps machines very clean while leaving a soft fluid film for ease of cleaning and reduced maintenance
Reduces oil mist and residues often associated with high lubricity alternatives
Delivers cost-effective performance as required in the automotive industry, yet meets the demanding standards of aerospace manufacturers
Contains no chlorinated compounds, nitrites, triazines, phenols, or sulfurized EP additives
Provides superior corrosion inhibition on all ferrous and nonferrous metals
Forms stable microemulsion in hard water environments
Compatible with a very wide range of material including aluminum, magnesium and copper alloys, cast iron, and many plastics and composites
Provides exceptional sump life
Requires no special disposal or recycling techniques
RPO 6BF is a barium-free, nonstaining, water displacing, thin-film corrosion inhibitor or rust preventative which can be used on a variety of metals. RPO 6BF is designed to provide indoor corrosion inhibition. RPO 6BF provides excellent protection for bearings and other precision parts, in-process parts in storage, as well as parts in transit.
Barium free
Light film for limited carryoff
Excellent corrosion inhibition, generally in excess of six months in dry storage
Nonstaining and RPO 6BF will provide cleaning action as well
Water displacing to help prevent rust due to water trapped under the protective film
Oxidation resistant to resist tarnishing over long storage periods
V.O.C. 493/gal
Easily removed with detergent cleaners, such as CLEAN 2029 “One Step”
Humidity Cabinet Test: No rust at 650 hours (ASTM D1748)
TRIM® TC 248pH Adjuster RELEASED: 2009-02-20
TRIM® TC 248 is an amine-based pH adjuster used to replenish depleted alkalinity in metalworking fluid working solutions.
TC 248 is usually added at concentrations between 0.05% - 0.25% (50 – 2,500 ppm) to help maintain pH, improve corrosion inhibition, and improve emulsion stability. A 0.1% add of TRIM TC 248 will typically increase the pH of a 7.0 pH fluid to approximately 8.0 - 8.5.
Overuse of this product may cause ammonia and/or amine blush; therefore, care should be taken not to exceed recommended add rates.
As formulated, TC 248 does not contain MEA, DEA, TEA, Cu, or Boron.
TRIM® OSA is a clear oil additive containing inactive sulfur. TRIM OSA has outstanding lubricity in all circumstances and provides extreme pressure anti-weld at high speeds and loads. Some significant uses of TRIM OSA include:
As an additive to straight grinding oils, will reduce heat, misting, and allow increased feed rates in creepfeed applications.
Has been used with great success to extend the life of thread-forming taps and thread-rolling dies.
In Swiss-type screw machines using solid carbide bushings, dramatically increases bushing life.
Compatible with all TRIM® straight oils, and TRIM® TAP LIGHT, TRIM® TAP HEAVY, and TRIM® TAP NC.
TRIM® OCA is a clear oil additive containing chlorinated paraffins. OCA has outstanding anti-welding and extreme pressure properties at moderate to heavy speeds and loads. Some significant uses of OCA include:
Good lubricity properties in addition to anti-weld
Used with great success to extend the life of taps and form tools in screw machining operations
Particularly effective on ferrous metals and aluminum
Compatible with all TRIM® straight oils, TRIM® TAP LIGHT, and TRIM® TAP HEAVY
For additions to straight cutting oils in screw machine operations, a starting rate of 5% is recommended
For very heavy-duty tasks, such as threading hard stainless or alloy steels, try starting at up to 15%
An effective booster additive for recycling straight cutting oil at an add rate of 1%-3%
There is no maximum rate; OCA can be used neat for tasks such as high-speed tapping
TRIM® E906 is a premium, low-foaming formula combining the newest available technology with our proven emulsion-based cutting platform. E906 delivers consistent machining and grinding performance on a wide range of materials and applications. The stable and predictable performance of E906 makes it a first choice for manufacturers doing work for industries as diverse as aerospace, automotive, energy, and specialty job shops. E906 offers a unique blend of both mechanical and extreme pressure lubricity agents.
Longer operational life than competitive fluids
Highly effective, extreme pressure additives control built-up edge
E906 is effective in a wide range of operations from production surface and centerless grinding to heavy-duty broaching, gear hobbing, surface, pocket, and thread milling
Low odor for pleasant operating environment
Tight emulsion reduces carryoff and gets the fluid to the point of cut
In high-speed turning and milling, E906 has the right balance of cooling and lubrication to provide great tool life and surface finishes
Low foam and low mist make it a first choice for high-pressure, high-volume coolant systems
Protects the machine tool surfaces while also preventing sticky ways, chucks, tool holders, and fixtures
Coolant is easily removed with water, working solution, or TRIM® CLEAN aqueous cleaners
Easy recycling or disposal with conventional techniques and equipment
Does not contain or test positive for phenol
Will run effectively for long periods without the need for costly additives
Effectively Remove Oil from Coolants and Washing Solutions RELEASED: 2008-05-21
Tramp oil is a major source of problems associated with water miscible cutting and grinding fluids.
Tramp oil contributes to the growth and formation of:
coolant-destroying bacteria
undesirable residues on machine tools and workpieces
smoke and oil mist in shop atmospheres
These problems result in:
shortened coolant life
poor material removal rates
poor surface finish and size control
decreased tool and wheel life
Numerous devices (“floating ropes,” wheels, and belts) have been developed over the years to remove “free floating“ tramp oil from the surface of coolant. While they have all worked to one degree or another, they generally have been either “troublesome,“ high maintenance, relatively ineffective, or able to operate only on limited liquid level fluctuations. To overcome the shortcomings of existing tramp oil skimming devices, Master Chemical has introduced the SCROUNGER® Oil Skimmer.
As a “belt-type” skimmer, these units are effective in removing floating oil from widely fluctuating liquid levels of coolants or parts washing solutions. The SCROUNGER® features a revolutionary new oleophilic belt and a totally new concept of stripping the separated oil from the belt. The SCROUNGER® Jr. uses the same “oil loving“ belt, but uses a more compact scraper blade to strip the separated oil from the belt.
FEATURES
115 volt, single phase, 50/60 Hz
heavy-duty, impedence-protected, fan-cooled drive motor with hardened shaft and needle bearings (220 volt,
single phase, 50 Hz also available)
open, accessible oil-collecting tray with a convenient drain connector
“oil loving“ oleophilic belt (purchased separately)
heavy-duty steel construction, with industrial-grade enamel paint
BENEFITS
fast, simple belt changing
low maintenance
lower hang roller that will not fall off in the machine sump even in turbulent conditions
OPTIONS
dewatering tray
portable kit
special length belts available on special order
special belt materials available for high temperature or pH applications on special order
